Our Brands
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Reich
The company Reich
Website ReichReich is a German company founded in 1975. Apart from producing movers they built all kinds of caravan accessories. Most water taps in a caravan are from market leader Reich. The factory is located in Eschenburg in the German state Hessen, where 150 employees work. In the Netherlands and UK it has affiliates. The Reich movers are largely made and assembled in Germany. Here at CaravanMoverShop we have visited Reich premises in Eschenburg many times, to help them to develop the EasyDriver product range.
Reich EasyDriver
The EasyDrivers are the third generation Reich movers. There are three models, the semi-automatic Basic and Active and the fully-automatic Pro. With the Basic and Active you connect the rollers to the tire by means of a pendulum movement. This is lighter than pivoting the claws. The difference between the Basic and the Active is that the Active uses a water-resistant plastic cover. These models have two power varieties for a single-axis caravan. The numbers refer to the maximum weight in tons, the 1.8 (1800 kg) and the 2.3 (2300 kg).
The Reich EasyDriver 2.3 models are the most powerful movers we offer. We advise you to use the EasyDriver 1.8 with caravans up to 1500 kg. With this device you can drive up a wedge of 25% without overloading the engines.
Some caravans with a BPW chassis allow the fitting of a Reich Pro BPW with minimal loss of ground clearance. The chassis needs to have a special space to fit the mover. This chassis has been on the market for a few years but is to be found mostly underneath the Hobby caravan model 2017 and onwards. All EasyDrivers use comfort remote control handsets allowing you to steer to the left and right while maneuvering the caravan. The rollers have a good grip on the tires. The weight of the mover itself is approximately 33 kg.
Reich EasyDriver Basic 2.3

The Reich EasyDriver Basic 2.3 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. This is a semi-automatic mover. Actuation is done with hand crank. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. On the integrated indicator can be read if the mover is correctly engaged against the tires. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2300 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 2000 kg. The actual weight of the mover itself (our measurement) without battery is approximately 34 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.7 cm. The mover needs an installation length of 36 cm /motor 30 cm. The metal parts are galvanized. The drive motor has 2 Motor brushes. The mover is introduced in 2014.
installation dimensions:
Foto Reich EasyDriver Basic 2.3
EasyDriver Basic 2.3 fitted (the looks of every caravan is different):
Reich EasyDriver Active 2.0

The Reich EasyDriver Active 2.0 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. This is a semi-automatic mover. Actuation is done with hand crank. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. On the integrated indicator can be read if the mover is correctly engaged against the tires. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2000 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 1550 kg. The actual weight of the mover itself (our measurement) without battery is approximately 33 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.7 cm. The mover needs an installation length of 36 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2021.
installation dimensions:
Foto Reich EasyDriver Active 2.0
EasyDriver Active 2.0 fitted (the looks of every caravan is different):
Reich EasyDriver Active 1.8

The Reich EasyDriver Active 1.8 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. This is a semi-automatic mover. Actuation is done with hand crank. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. On the integrated indicator can be read if the mover is correctly engaged against the tires. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 1800 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 1550 kg. The actual weight of the mover itself (our measurement) without battery is approximately 33 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.7 cm. The mover needs an installation length of 36 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2018
and delivered till 2021
installation dimensions:
Foto Reich EasyDriver Active 1.8
EasyDriver Active 1.8 fitted (the looks of every caravan is different):
Reich EasyDriver Active 2.3

The Reich EasyDriver Active 2.3 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. This is a semi-automatic mover. Actuation is done with hand crank. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. On the integrated indicator can be read if the mover is correctly engaged against the tires. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2300 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 2000 kg. The actual weight of the mover itself (our measurement) without battery is approximately 35 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.7 cm. The mover needs an installation length of 36 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2018.
installation dimensions:
Foto Reich EasyDriver Active 2.3
EasyDriver Active 2.3 fitted (the looks of every caravan is different):
Reich EasyDriver Pro 1.8

The Reich EasyDriver Pro 1.8 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. The swiveling of the rollers towards the tire is fully automatic with the pressure on the tires controlled by the electronics.
The pressure builds up to 4500 Nm. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. The actuator motor automatically stops as soon as the pressure is sufficient or as soon as the mover has been pushed fully forward. In case of a completely discharged or defective battery, the mover can easily be removed from the beltwith an included special key. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 1800 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 1500 kg. The actual weight of the mover itself (our measurement) without battery is approximately 31 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.7 cm. The mover needs an installation length of 35 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2014.
installation dimensions:
Foto Reich EasyDriver Pro 1.8
EasyDriver Pro 1.8 fitted (the looks of every caravan is different):
Reich EasyDriver Pro 2.0

The Reich EasyDriver Pro 2.0 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. The swiveling of the rollers towards the tire is fully automatic with the pressure on the tires controlled by the electronics.
The pressure builds up to 4500 Nm. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. The actuator motor automatically stops as soon as the pressure is sufficient or as soon as the mover has been pushed fully forward. In case of a completely discharged or defective battery, the mover can easily be removed from the beltwith an included special key. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2000 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 1550 kg. The actual weight of the mover itself (our measurement) without battery is approximately 31 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.7 cm. The mover needs an installation length of 35 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2021.
installation dimensions:
Foto Reich EasyDriver Pro 2.0
EasyDriver Pro 2.0 fitted (the looks of every caravan is different):
Reich EasyDriver Pro 2.3

The Reich EasyDriver Pro 2.3 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. The swiveling of the rollers towards the tire is fully automatic with the pressure on the tires controlled by the electronics.
The pressure builds up to 4500 Nm. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. The actuator motor automatically stops as soon as the pressure is sufficient or as soon as the mover has been pushed fully forward. In case of a completely discharged or defective battery, the mover can easily be removed from the beltwith an included special key. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2300 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 2000 kg. The actual weight of the mover itself (our measurement) without battery is approximately 33 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.7 cm. The mover needs an installation length of 35 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2014.
installation dimensions:
Foto Reich EasyDriver Pro 2.3
EasyDriver Pro 2.3 fitted (the looks of every caravan is different):
Reich EasyDriver Pro 2.0 BPW-Hobby

The Reich EasyDriver Pro 2.0 BPW-Hobby is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. The swiveling of the rollers towards the tire is fully automatic with the pressure on the tires controlled by the electronics.
The pressure builds up to 4500 Nm. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. The actuator motor automatically stops as soon as the pressure is sufficient or as soon as the mover has been pushed fully forward. In case of a completely discharged or defective battery, the mover can easily be removed from the beltwith an included special key. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2000 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 1550 kg. The actual weight of the mover itself (our measurement) without battery is approximately 34 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 2 cm. The mover needs an installation length of 35 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2021.
Foto Reich EasyDriver Pro 2.0 BPW-Hobby
EasyDriver Pro 2.0 BPW-Hobby fitted (the looks of every caravan is different):
Reich EasyDriver Pro 2.3 BPW-Hobby

The Reich EasyDriver Pro 2.3 BPW-Hobby is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. The swiveling of the rollers towards the tire is fully automatic with the pressure on the tires controlled by the electronics.
The pressure builds up to 4500 Nm. The distance traveled when swiveling is 5 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 3 cm. The actuator motor automatically stops as soon as the pressure is sufficient or as soon as the mover has been pushed fully forward. In case of a completely discharged or defective battery, the mover can easily be removed from the beltwith an included special key. The mover has a worm wheel transmission that prevents the caravan from rolling back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 6 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2300 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of 2000 kg. The actual weight of the mover itself (our measurement) without battery is approximately 36 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 2 cm. The mover needs an installation length of 35 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2014.
Foto Reich EasyDriver Pro 2.3 BPW-Hobby
EasyDriver Pro 2.3 BPW-Hobby fitted (the looks of every caravan is different):
Reich EasyDriver Infinity 2.5

The Reich EasyDriver Infinity 2.5 is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. The swiveling of the rollers towards the tire is fully automatic with the pressure on the tires controlled by the electronics.
The pressure builds up to 4500 Nm. The distance traveled when swiveling is 7 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 5 cm. The actuator motor automatically stops as soon as the pressure is sufficient or as soon as the mover has been pushed fully forward. In case of a completely discharged or defective battery, the mover can easily be removed from the beltwith an included special key. Before use, you have to release the safety switch. The mover has a built-in automatic brake, therefore the caravan does not roll back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 8 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2500 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of - kg. The actual weight of the mover itself (our measurement) without battery is approximately 33 kg. The mover is relatively low in weight.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 5.5 cm. The mover needs an installation length of 36 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2020.
Video Reich EasyDriver Infinity 2.5
Foto Reich EasyDriver Infinity 2.5
EasyDriver Infinity 2.5 fitted (the looks of every caravan is different):
Reich EasyDriver Infinity 2.5 BPW-Hobby

The Reich EasyDriver Infinity 2.5 BPW-Hobby is for caravans with single axle caravans. The electronics have a softstart and stopfunction. This makes manoeuvring the caravan gently and has less effect on the chassis. Manoeuvring is done with a remote control (434 MHz) with push buttons. You can turn the caravan around the axle.
Technic
This mover has an operation with comfort. Thus making it possible to adjust the caravan a little left or right while manoeuvring forwards and backwards. The swiveling of the rollers towards the tire is fully automatic with the pressure on the tires controlled by the electronics.
The pressure builds up to 4500 Nm. The distance traveled when swiveling is 7 cm. De rollen staan ongeveer 2 cm van de band afgesteld, de druk van de rol in de band is dus maximaal 5 cm. The actuator motor automatically stops as soon as the pressure is sufficient or as soon as the mover has been pushed fully forward. In case of a completely discharged or defective battery, the mover can easily be removed from the beltwith an included special key. Before use, you have to release the safety switch. The mover has a built-in automatic brake, therefore the caravan does not roll back on a slope. The wear-resistant maintenance-friendly aluminium drive rollers have a diameter of 8 cm, this ensures optimal grip on the tires.
The manufacturer recommends this mover for caravans up to 2500 kg /15%. We expect with our advise taking a short slope of 20% should be no problem, thus our advise with our set 2 for this mover is for caravans with a maximum weight of - kg. The actual weight of the mover itself (our measurement) without battery is approximately 36 kg.
The height for the installation is 12 cm. The loss of ground clearance after installation with an appropriate chassis is 3 cm. The mover needs an installation length of 36 cm. The metal parts are galvanized. The mover is optimailly protected against moisture, so that the risk of malfunctions is minimal when mounted behind the wheels. The drive motor has 2 Motor brushes. The mover is introduced in 2020.